Tyler County, WV Elevation & Topographic Map

Topographic elevation map of Tyler County, West Virginia, shaded from 600 ft on the west side to 1,510 ft on the east side
Elevation
1,510 ft 460 m1,280 ft 390 m1,170 ft 355 m940 ft 285 m720 ft 220 m600 ft 185 m
Contours every 500 ft, bold every 2,500 ft
USGS 3DEP · U.S. Census Bureau
How to use this mapviews, tools and data
Elevation
Ground colored by height from green (lowest) to white (highest), with contour lines every 40–500 ft (USGS data).
Satellite
A 2016 satellite photo at 33 ft (10 m) detail; contours off.
3D
Tilt and turn the terrain; hills are raised 1.5×, or set ×1 for true height.
Click or tap anywhere
The exact elevation of that spot in ft and m.
Measure
Pick two points for the climb, descent and grade along a straight line.
County area
Fades everything outside the official county boundary (US Census).

Elevation Data

Tyler County averages about 950 ft (290 m) above sea level across all its land. Its ground runs from 600 ft on the west side to 1,510 ft on the east side.

Average elevation
950 ft 290 m
all land inside the county
Highest
1,510 ft 460 m
on the east side
Lowest
600 ft 185 m
on the west side

Tyler County spans about 910 ft of height, so no single spot tells the whole story. The ruler shows where most of its land lies, and where the other numbers you'll see come from.

FigureElevation
Average of all land950 ft290 m
Highest point
Inside the county, on the east side
1,510 ft460 m
Lowest point
Inside the county, on the west side
600 ft185 m

Elevation profile, west to east

9.5 mi west to east through Sistersville.

Topographic Map

Topographic elevation map of Tyler County, West Virginia, shaded from 600 ft on the west side to 1,510 ft on the east side
County boundary (dashed) over shaded terrain, with contours every 100 ft (30 m).
Location
County in West Virginia, United States
Population
7,843 2024 est.
Land area
256.3 sq mi + 4.4 sq mi water
Density
31 per sq mi
Time zone
Eastern UTC−5 / −4
Landform region
Appalachian Plateaus
Drains to
Gulf of America
⤓ Download this map

WebP, 1200 × 900. Free to use: credit “ElevationOf.com” with a link to this page.

Sources: U.S. Census Bureau, USGS

Nearby Places

All 4 towns in Tyler County by typical elevation
  1. Middlebourne740 ft
  2. Paden City partly660 ft
  3. Sistersville650 ft
  4. Friendly620 ft
How we measure
  • Average: every USGS 3DEP bare-earth cell of land inside the Census county boundary (TIGER/Line, Jan 1 2026), weighted equally, on a 1 arc-second (≈100 ft, 30 m) grid. Land means the boundary minus Census area water.
  • Highest and lowest: the highest land cell. Lowest: the lowest land cell; coastal ground within 3 ft (1 m) of named tidal water counts as sea level.
  • Nearby Places: neighboring counties and rankings use each one's average elevation, on its own grid, the same figure its page shows. Peaks and hills: the highest summits inside the county with at least 980 ft (300 m) of prominence, then the highest federal (GNIS) summits inside it when there are fewer than 5; each is the 3DEP top on a ~7 ft (2 m) window, or the NGS published height when a usable survey mark sits within 160 ft (50 m) of it (shown as published).
  • Towns: each town's typical elevation (population-weighted median of its own 2020 blocks at 1 arc-second); a town is listed when any of its 2020 residents live in the county.
  • Rounding: computed heights are rounded to 10 ft (5 m), or to 1 ft (1 m) under 100 ft; 3DEP is good to about a meter, not a foot. Published figures (NGS survey heights) are shown as their publisher gives them.
  • Datum: North American Vertical Datum of 1988 (NAVD 88). NGS plans to replace NAVD 88 with a new datum (NAPGD2022); heights will then shift slightly.
  • Sources: USGS 3DEP, GNIS, Watershed Boundary Dataset and physiographic provinces; U.S. Census Bureau (TIGER boundaries and water, 2020 blocks, 2024 population estimates, county adjacency); NOAA NGS survey heights; BTS time zones. All public domain.