Melfa, VA Elevation & Topographic Map
Elevation
76 ft 23 m68 ft 21 m63 ft 19 m55 ft 17 m47 ft 14 m43 ft 13 m
Contours every 40 ft, bold every 200 ft
USGS 3DEP · U.S. Census Bureau
How to use this mapviews, tools and data
- Elevation
- Ground colored by height from green (lowest) to white (highest), with contour lines every 40–500 ft (USGS data).
- Satellite
- A 2016 satellite photo at 33 ft (10 m) detail; contours off.
- 3D
- Tilt and turn the terrain; hills are raised 1.5×, or set ×1 for true height.
- Click or tap anywhere
- The exact elevation of that spot in ft and m.
- Measure
- Pick two points for the climb, descent and grade along a straight line.
- Town area
- Fades everything outside the official town limits (US Census).
Elevation Data
Melfa sits at about 48 ft (15 m) above sea level, worked out from 2020 Census block heights on USGS 3DEP, weighted by residents.
Typical elevation
48 ft 15 m
most residents: 44–51 ft
Lowest
43 ft 13 m
on the southwest side
Highest
53 ft 16 m
on the northwest side
Average
48 ft 15 m
all land inside town limits
Melfa is nearly flat: its ground varies by only about 10 ft, so the figures below sit close together.
| Figure | Elevation |
|---|---|
| Typical Where people live: half of residents higher, half lower | 48 ft15 m |
| Highest point Inside town limits, on the northwest side | 53 ft16 m |
| Lowest point Inside town limits, on the southwest side | 43 ft13 m |
| Town center USGS map point for Melfa | 50 ft15 m |
| Airport (MFV) FAA airport elevation, the highest point of its runways, 0.8 mi west of the town limits | 48 ft15 m |
| Average of all land | 48 ft15 m |
Topographic Map
- Location
- Town in Accomack County, Virginia, United States
- Population
- 400 2024 est.
- Land area
- 0.3 sq mi
- Density
- 1,375 per sq mi
- Coordinates
- 37.6493° N, 75.7413° W
- Time zone
- Eastern UTC−5 / −4
- Landform region
- Coastal Plain
- Drains to
- Atlantic Ocean
- Airport
- Accomack County (MFV) 48 ft
- ZIP codes 1
- 23410
⤓ Download this map
WebP, 1200 × 900. Free to use: credit “ElevationOf.com” with a link to this page.
Sources: U.S. Census Bureau, USGS, FAA
Nearby Places
Nearby towns by typical elevation
- Melfa48 ft
- Onley43 ft
- Tasley42 ft
- Keller38 ft
- Pungoteague34 ft
- Savageville32 ft
- Onancock19 ft
- Wachapreague7 ft
- Bobtown7 ft
- Locust Mount6 ft
- Harborton6 ft
Rankings by typical elevation
- Towns in Virginia599th highest of 700
- Towns in Accomack Countyhighest of 49
Peaks and hills nearest, by height
- Italian Hill20 ft
How we measure
- Typical elevation: the population-weighted median: every 2020 Census block inside the town limits, at its USGS 3DEP height, weighted by the people who live there. Half of residents live higher, half lower.
- Lowest, highest, average: USGS 3DEP bare-earth heights on a 1 arc-second (≈100 ft, 30 m) grid, land only, inside the Census town limits (TIGER, Jan 1 2026).
- Nearby Places: nearby towns and rankings use each town's typical elevation, so every town is compared like for like. Rankings count every city, town, township and census-designated place, including places inside a town. Peaks and hills: the nearest summits with at least 980 ft (300 m) of prominence within 62 mi (100 km), then federal (GNIS) summits within 16 mi (25 km) when there are fewer than 5; each is the 3DEP top on a ~7 ft (2 m) window, or the NGS published height when a usable survey mark sits within 160 ft (50 m) of it (shown as published).
- Rounding: computed heights are rounded to 10 ft (5 m), or to 1 ft (1 m) under 100 ft; 3DEP is good to about a meter, not a foot. Published figures (FAA airport elevation, NGS survey heights) are shown as their publisher gives them.
- Datum: North American Vertical Datum of 1988 (NAVD 88). NGS plans to replace NAVD 88 with a new datum (NAPGD2022); heights will then shift slightly.
- Sources: USGS 3DEP, GNIS, Watershed Boundary Dataset and physiographic provinces; U.S. Census Bureau (boundaries, 2020 blocks, 2024 population estimates, Gazetteer areas, ZIP code areas); FAA airport data; BTS time zones. All public domain.