Daniels County, MT Elevation & Topographic Map

Topographic elevation map of Daniels County, Montana, shaded from 2,210 ft on the southeast side to 3,140 ft on the northwest side
Elevation
3,140 ft 955 m2,910 ft 885 m2,790 ft 850 m2,560 ft 780 m2,320 ft 710 m2,210 ft 670 m
Contours every 500 ft, bold every 2,500 ft
USGS 3DEP · U.S. Census Bureau
How to use this mapviews, tools and data
Elevation
Ground colored by height from green (lowest) to white (highest), with contour lines every 40–500 ft (USGS data).
Satellite
A 2016 satellite photo at 33 ft (10 m) detail; contours off.
3D
Tilt and turn the terrain; hills are raised 1.5×, or set ×1 for true height.
Click or tap anywhere
The exact elevation of that spot in ft and m.
Measure
Pick two points for the climb, descent and grade along a straight line.
County area
Fades everything outside the official county boundary (US Census).

Elevation Data

Daniels County averages about 2,640 ft (805 m) above sea level across all its land. Its ground runs from 2,210 ft on the southeast side to 3,140 ft on the northwest side.

Average elevation
2,640 ft 805 m
all land inside the county
Highest
3,140 ft 955 m
on the northwest side
Lowest
2,210 ft 670 m
on the southeast side

Daniels County spans about 930 ft of height, so no single spot tells the whole story. The ruler shows where most of its land lies, and where the other numbers you'll see come from.

FigureElevation
Average of all land2,640 ft805 m
Highest point
Inside the county, on the northwest side
3,140 ft955 m
Lowest point
Inside the county, on the southeast side
2,210 ft670 m

Elevation profile, west to east

45 mi west to east through Scobey.

Topographic Map

Topographic elevation map of Daniels County, Montana, shaded from 2,210 ft on the southeast side to 3,140 ft on the northwest side
County boundary (dashed) over shaded terrain, with contours every 100 ft (30 m).
Location
County in Montana, United States
Population
1,625 2024 est.
Land area
1,426.3 sq mi + 0.4 sq mi water
Density
1.1 per sq mi
Time zone
Mountain UTC−7 / −6
Landform region
Great Plains
Drains to
Gulf of America 96%
⤓ Download this map

WebP, 1200 × 900. Free to use: credit “ElevationOf.com” with a link to this page.

Sources: U.S. Census Bureau, USGS

Nearby Places

All 4 towns in Daniels County by typical elevation
  1. Peerless2,840 ft
  2. Flaxville2,780 ft
  3. Whitetail2,510 ft
  4. Scobey2,480 ft
How we measure
  • Average: every USGS 3DEP bare-earth cell of land inside the Census county boundary (TIGER/Line, Jan 1 2026), weighted equally, on a 1 arc-second (≈100 ft, 30 m) grid. Land means the boundary minus Census area water.
  • Highest and lowest: the highest land cell. Lowest: the lowest land cell; coastal ground within 3 ft (1 m) of named tidal water counts as sea level.
  • Nearby Places: neighboring counties and rankings use each one's average elevation, on its own grid, the same figure its page shows. Peaks and hills: the highest summits inside the county with at least 980 ft (300 m) of prominence, then the highest federal (GNIS) summits inside it when there are fewer than 5; each is the 3DEP top on a ~7 ft (2 m) window, or the NGS published height when a usable survey mark sits within 160 ft (50 m) of it (shown as published).
  • Towns: each town's typical elevation (population-weighted median of its own 2020 blocks at 1 arc-second); a town is listed when any of its 2020 residents live in the county.
  • Rounding: computed heights are rounded to 10 ft (5 m), or to 1 ft (1 m) under 100 ft; 3DEP is good to about a meter, not a foot. Published figures (NGS survey heights) are shown as their publisher gives them.
  • Datum: North American Vertical Datum of 1988 (NAVD 88). NGS plans to replace NAVD 88 with a new datum (NAPGD2022); heights will then shift slightly.
  • Sources: USGS 3DEP, GNIS, Watershed Boundary Dataset and physiographic provinces; U.S. Census Bureau (TIGER boundaries and water, 2020 blocks, 2024 population estimates, county adjacency); NOAA NGS survey heights; BTS time zones. All public domain.